Set windows logoff time

In some cases, Windows will want you to fully reboot the system before the settings can fully be applied. If the steps above do not work for you, you may find the post below helpful. The post below will work on both Windows 10 and Windows 11 and will change the power settings even if the device is controlled in a corporate environment. How to keep Windows awake with PowerToys.

This post showed you how to configure Windows 11 timeout settings for when to turn off the screen after certain time when the system is not in used. Your email address will not be published. Unsolicited bulk mail or bulk advertising. Any link to or advocacy of virus, spyware, malware, or phishing sites. Any other inappropriate content or behavior as defined by the Terms of Use or Code of Conduct.

Any image, link, or discussion related to child pornography, child nudity, or other child abuse or exploitation. Details required : characters remaining Cancel Submit people found this reply helpful.

Was this reply helpful? Yes No. Sorry this didn't help. Thanks for your feedback. This thread is locked. You can follow the question or vote as helpful, but you cannot reply to this thread. I have the same question Report abuse. Details required :. The default value is 3. The allowed range is If not specified, the local computer will resynchronize. Otherwise, wait for resynchronization to complete before returning.

This is used for compatibility purposes. The default is 2 seconds. If not specified, the default is the local computer. When specifying multiple peers, this option must be enclosed in quotes. This setting is only meaningful on domain controllers.

YES : This computer is a reliable time service. NO : This computer is not a reliable time service. If not specified, the default value is the local computer. In verbose mode, display the undefined or unused setting too. Valid values are 0 to A range of numbers is valid, in addition to single numbers, such as ,, Value is for logging all information.

Set client to use two time servers To set a client computer to point to two different time servers, one named ntpserver. To configure a client computer that is currently synchronizing time using a manually-specified computer to synchronize time automatically from the AD domain hierarchy, run the following following:.

To check a client configuration from a Windows-based client computer that has a host name of contosoW1 , run the following command:. The output of this command displays a list of W32time configuration parameters that are set for the client. Windows Server has improved the time synchronization algorithms to align with RFC specifications. Therefore, if you want to set the local time client to point to multiple peers, we recommended that you prepare three or more different time servers. If you have only two time servers, you should specify the Ntpserver UseAsFallbackOnly flag 0x2 to de-prioritize one of them.

For example, if you want to prioritize ntpserver. Additionally, you can run the following command and read the value of NtpServer in the output:. In order for W32tm. Then, to adjust the computer clock by using the clock rate, W32tm. This algorithm varies depending on the version of Windows:. MaxAllowedPhaseOffset is configurable in the registry. However, the registry parameter is measured in seconds instead of clock ticks.

This command produces output that resembles the following. The output presents the poll interval in both clock ticks and in seconds.

The equations use the value measured in seconds the value in parentheses. The output presents the clock rate in seconds. To see the SystemClockRate value in clock ticks, use the following formula:. For example, if SystemClockRate is 0. For full descriptions of the configurable parameters and their default values, see Config entries later in this article. The following examples show how to apply these calculations for Windows Server R2 and earlier versions.

In this case, if you want to set the clock back slowly, you would also have to adjust the values of PhaseCorrectRate or UpdateInterval in the registry to make sure that the equation result is TRUE. The Windows Time service stores a number of configuration properties as registry entries. It stores configuration information that the policies define in the Windows registry, and then uses those registry entries to configure the registry entries specific to the Windows Time service.

As a result, the values defined by Group Policy overwrite any pre-existing values in the Windows Time service section of the registry. Some of the preset GPO settings differ from the corresponding default Windows Time service registry entries.

Windows loads these settings into the policy area of the registry under the following subkey:. Then Windows uses the policy settings to configure the related Windows Time service registry entries under the following subkey:.

The following table lists the policies that you can configure for the Windows Time service, and the registry subkeys that those policies affect. When you remove a Group Policy setting, Windows removes the corresponding entry from the policy area of the registry. This information is provided as a reference for use in troubleshooting and validation.

Windows registry keys are used by W32Time to store critical information. Don't change these values. Modifications to the registry are not validated by the registry editor or by Windows before they are applied.

If the registry contains invalid values, Windows may experience unrecoverable errors. Some of the parameters in the registry are measured in clock ticks and some are measured in seconds. To convert the time from clock ticks to seconds, use these conversion factors:.

Note Zero is not a valid value for the FrequencyCorrectRate registry entry. HoldPeriod All versions Controls the period of time for which spike detection is disabled in order to bring the local clock into synchronization quickly. A spike is a time sample indicating that time is off a number of seconds, and is usually received after good time samples have been returned consistently.

The default value on domain members is 5. The default value on stand-alone clients and servers is 5. LargePhaseOffset All versions Specifies that a time offset greater than or equal to this value in 10 -7 seconds is considered a spike. A network disruption such as a large amount of traffic might cause a spike. A spike will be ignored unless it persists for a long period of time.

The default value on domain members is Asked 6 years, 5 months ago. Active 2 years, 11 months ago. Viewed k times. Computer is powered Every time i go out for minutes it go to login screen, broke all my opened ssh session etc. Anyone have same? Any way fix it? Maybe there is somewhere logoff timeout option? Improve this question. Have you checked the event log to see if you were logged out, or the system had an unexpected reboot? No, it not reboot.

It just logoff, all applications are here and same state as before, just disconnected seams like it go fast sleep mode. It is not one time behavour. That was 5 times over last hour. Checked windows event log. It show "The system is entering sleep. Sleep Reason: System Idle", by "kernel-power".

However all settings in current scheme are "never" — arheops. Did you find a solution to your problem? I also have this problem. Suddenly appeared after new Win 10 update. Show 3 more comments.