Buster setup

Keep me logged in on this device Forgot your username or password? Don't have an account? Sign up for free! What do you need help on?

Cancel X. Topic Archived Page 1 of 3 Next Last. Sign Up for free or Log In if you already have an account to be able to post messages, change how messages are displayed, and view media in posts. I have all the buster parts. Any thoughts? KlownArt 13 years ago 2. I used to know the best setup. It would max out Power, Energy, and put rapid extremely high. Range would be decent enough. Let's face it, you do not need that much range. I seem to remember Buster Unit gamma being included in it.

Is gamma the upside down horeshoe? Anyway if you or anyone else remembers the best buster setup feel free to post it. KlownArt 13 years ago 4. That is the gamma symbol. IMO this is the most useful setup not counting the Buster Max. The domain name should be the same on all other nodes on your network.

Here, you need to set a strong root password for your administrative account. First, create a user account for non-administrative activities. This user can be configured to gain root privileges using sudo. Next, create a username for the above user. Do not forget that the username must begin with a lower-case letter followed by a combination of numbers and more lower-case letters.

Set a strong and secure password made up of a mixture of letters both lowercase and uppercase, numbers, and special characters for the new user account. Confirm the password and click Continue. There are several disk partitioning options but we will use Manual partitioning. So select it and click Continue. The installer will display all currently installed disks or configured partitions and mount points as well on your computer.

Select the disk you want to partition e. If you have selected an entire disk, the installer will show a warning message.

Once you have decided to partition the disk, select Yes to create a new empty partition table on the disk and click Continue. A new empty partition table has been created on the disk. Double click on it to create a new partition. Then double click on Create a new partition and enter the maximum size of the partition. Once you are done, click Continue. Next, make the new partition a primary partition and set it to be created at the beginning of the available space.

The installer will then choose the default partition settings such as file system type, mount point, mount options, label, etc. You can make changes according to your requirements. When you have done, select Done setting up the partition, and click Continue. The free space is also displayed, which will be configured as swap space as explained next.

From the previous interface, double click on the free space 4 GB in this case , go through the same steps we used to create the root partition. Click Create a new partition, enter its size, then set it as a Logical partition and configure it to be created at the end of available space.

At the partition settings interface, set Use as value as swap area double click on the default value to get more options. Then go to Done settings up the partition to continue. Once all the necessary partitions root and swap area are created, your partition table should look similar to what is in the following screenshot. And double click on Finish partitioning and write changes to disk. Then accept the recent changes made to the disk during the partitioning process to allow the installer to write them to the disk.

When you login to Raspbian Buster Lite for the first time, it will prompt you to change the default password password:. If you want to take that advice, you can change the password of the pi user by entering the following command:. After entering raspberry as the current password and your new password twice, you will be able to change the password of the pi user.

Next, configure the locale settings for your Raspbian Buster Lite. When the Raspberry Pi Software Configuration Tool starts, follow through the screens to install your locale settings:. Once you are done with the changes, press Ctrl-X , Y and Enter to save the changes.

When you do so, the locale settings for Raspbian Buster Lite will persist through system reboots. If your Raspberry Pi does not reside in the British Summer Time timezone, then you may want to change the timezone of your Raspberry Pi. When raspi-config starts, you can change the Timezone of your Raspberry Pi. For example, if I want to change my Timezone to Singapore's timezone, I will go through the following screens:.

If you intend to deploy several Raspberry Pis in your home, you may want to give each of them a unique hostname. When raspi-config starts, follow through the following screens to change the hostname of your Raspberry Pi:. Clivant a. He owns techcoil. Quick References.